Door Headers
Leaks Over Sliding Doors
Water gets behind the trim over sliding door headers and runs down the track, rusting both.
Madison County · Unincorporated
Waco Metal Roof Coating
We do metal roof coating in Waco for machine sheds, barns and farm buildings, including sheds now working as shops, feed stores or rental storage.
Local Focus
Farm Sheds That Changed Jobs
No city government covers Waco, an unincorporated Madison County community outside both Richmond and Berea. Under the county's building code ordinance, the Madison County Building Inspector enforces the code, and barns, silos and machine sheds sit outside its scope.
Those exemptions are for buildings still used for farming. Once a machine shed becomes a welding shop, feed store or rental storage, its use has changed, and the Madison County Codes Office and the Kentucky HBC should hear about it before roof work begins.
- Sliding door tracks and headers checked for rust and leaks
- Eaves at open framing sealed and closed off
- Lean-to roofs tied into the main ridge detailed with fabric
Roof Conditions
Where Converted Sheds Leak Around Waco
Sheds built for equipment and later put to other uses share a few weak spots.
Lean-Tos
Lean-To Tie-Ins
Where a lean-to roof meets the main wall or ridge, the flashing joint opens and lets water into the wall.
Open Eaves
Open Eave Framing
Eaves left open for airflow let wind-driven rain and birds in, a problem under the roof once the shed holds stock or tools.
Panels
Nail-Down Panels On Wood Purlins
Older sheds often have panels nailed or screwed into wood purlins, and the fasteners loosen as the wood dries and shrinks.
Benefits
Benefits of Coating Your Roof
A coating gives a converted shed the dry roof its new use needs.
Ready For Its New Use
A sealed roof and closed-off eaves keep stock, tools and stored goods dry in a building first put up for tractors, which a shop or store needs before shelving goes in.
Lean-To Joints Sealed
Fabric and coating across the tie-in joint stop the leak where two roofs meet, after new flashing goes in where the old joint has opened.
Lower Cost Than A New Building
Solid panels and framing stay, so a working shed becomes a working shop without new steel, new purlins or a long stretch with the roof open.
Insulation If Needed
Shops that heat in winter can add spray foam over the panels before the topcoat, burying the old screws and nails at the same time.
Coating Options
Commercial Roof Coating Options for Waco
Waco sheds and farm buildings get one of these, chosen by how the building is used.
Metal Coating For Storage Sheds
Sheds used for storage get sealed screws and laps under a base and top coat. Door header trim gets resealed too.
Metal Roof Coating
Foam For Heated Shops
Welding shops and workshops that heat in winter get foam for insulation, then a coating. The screws disappear under the foam.
Spray Foam Roofing
Silicone On Flat Lean-Tos
Shallow lean-to roofs that hold water get silicone where it sits. New flashing ties it to the main wall.
Silicone Roof CoatingWater Getting In Over The Doors?
Tell us which door and how the building is used now. Headers and lean-to joints are the usual starting points.
Process
How We Coat A Converted Shed In Waco
Five decisions, starting with what the building does now.
- On The Roof
Inspect Your Roof
We walk the panels and check the sliding door headers, the eave at open framing and any lean-to joined to the main ridge.
- Permits
Farm Building Or Changed Use?
A working farm shed sits outside the county ordinance. A shed now used as a shop, store or rental storage needs a call to the county and the state before roof work.
- Detail
Close In The Eaves?
Open eaves get closures or trim when the building now holds stock or tools that need to stay dry under the roof.
- Detail
How Is The Lean-To Joined?
The joint where a lean-to meets the main roof or wall gets new flashing where needed, then fabric and coating.
- System
Foam Or Coating Alone?
Heated shops take foam for insulation. Storage sheds usually need only the roof coating.
Nearby Towns
Other Towns In Our Service Area
Metal roof coating work takes us to these towns too. For other locations, call us or send us a message.
Berea
City permits, state plan review, equipment-heavy roofs.
Irvine
Estill County barns where condensation rusts panels from below.
Mount Vernon
Rockcastle County roofs with old skylight panels to sort.
Stanton
Powell County shops where gutters and downspouts matter most.
McKee
Jackson County roofs with purlins checked before coating.
Paint Lick
Garrard County roofs needing ridge cap and eave trim work.
Ravenna
River and rail town where roof panels get washed first.
Kingston
Outside Berea's line, with service masts through roof panels.
FAQ
Waco Metal Roof Coating Questions
What Waco owners ask about permits, pole barns and converted sheds.
Question about your own roof?
Call UsHow are farm buildings and shops around Waco treated for permits?
Working farm buildings fall outside the county building code. Waco is unincorporated, and the Madison County ordinance names the county Building Inspector while leaving barns, silos and machine sheds out of its scope.
A machine shed converted into a welding shop, feed store or rental storage has changed its use, and that building needs a call to the Madison County Codes Office and the Kentucky HBC before roof work begins.
Can a pole barn roof be coated?
If the panels are attached and the posts and purlins are solid, yes. Pole barns often have screw-down panels on wood purlins, so we check for rot where screws bite and for loose panels at the eave.
What gets checked at a sliding door?
The header trim, the track and the panel laps above it. Water that gets behind the header trim rusts the track and drips inside, so the trim is resealed or replaced before coating.
Do lean-to roofs need different treatment?
Often. Lean-tos tend to have less slope than the main roof, so they hold water longer. Many get silicone, plus new flashing where they meet the main building.
Should a converted shed get insulation?
For a heated or cooled shop, it is worth asking. Spray foam over the panels adds insulation and covers the screws in one step, ahead of the topcoat.
Does a shop conversion change the coating choice?
Sometimes. A heated shop gains from foam under the coating, while cold storage can take a coating alone. Mention how the building is used now on the first visit, since that sets both the system and the permit question.
Give Your Converted Shed A Dry Roof
Start a free estimate for your Waco building, or call to talk through the doors, lean-tos and panels.